As a swimming pool owner if you will want pool that sparkles like a stone basking in the desert sun, there’s three things you have to know about proper swimming pool maintenance.
In this short article I’m likely to break up all these essential points and explain why they’re so important.
Swimming Pool Maintenance Success Tip #1: Water Circulation. Consider your pool as a huge bucket of water. Without adequate circulation and water movement it quickly becomes a safe haven for bacteria and algae.
Without proper circulation any chemicals put into the water essentially because meaningless. Whatever you enhance the water isn’t circulated diamond brite pool finish problems, which, causes your free chlorine levels to quickly become depleted, your pH levels get elevated along with your Total Alkalinity levels. They are the 3 most important items to control and if they get free from whack, that creates a control reaction and it’s never pretty.
If that you don’t winterize your pool, run your equipment for 6 hours during the off season (when it’s too cold to swim) and 8-10 hours during summer time months. As an over-all guideline, you would like your pool to cycle all the water at least one time during the swimming season. Anything significantly less than that can result in significantly less than adequate water circulation and create chemistry issues.
Swimming Pool Maintenance Success Tip #2: Filtration. Filtering your swimming pool water is vital to fight pathogens and remove foreign particles from your water and keep your pool sparkly clean.
You can find 3 main forms of filtration systems. Sand filters, DE filters and cartridge filters. Each of them have their own maintenance needs, but don’t worry – the process is pretty simple and straight forward. For sand filters it’s as simple as backwashing the filter. Adjust your backwash valve to the backwashing position or adjust your multi-port valve appropriately and allow the water run for 90 seconds or before the water coming from the backwash is clean and clear. Backwash your filter anytime the pressure exceeds 5 PSI greater than normal operating pressure. You may also backwash your filter on a weekly basis, regardless of the filter pressure reading. You cannot over-backwash your filter.
For DE filters, the process is slightly more hours consuming. Within your filter dome, you have filter grids. These need to be removed and hosed down with a high pressure water hose. When you have a stress washer you may also use a good degreasing agent and mix it with the water. Make use of a very mild solution like 4 parts water to at least one part cleaner. I’m generally not a fan to getting a DE filter cleaning product from the bigger pool supply retailers because the pricing is astronomical and you likely have something that’ll work just fine under your drain right now. You may also use a mild muriatic acid mix (3 parts water to 1 part muriatic acid) along with your dishwashing detergent (just be sure to thoroughly rinse the grids to ensure there’s no detergent residue when you’ve completed the job).
Finally, you have cartridge filters. For proper swimming pool maintenance when you yourself have this kind of filter, the process is similar to cleaning a DE filter.
Take away the cartridge(s) from the canister and thoroughly hose it down. When you have a high pressure water hose, you may also use a mild muriatic acid mix or standard dishwashing detergent. Heavily spray the cartridge until it’s visibly clean and reassemble the filter unit. With a DE filter or cartridge make certain there’s no leaks at the o-ring whenever you start the equipment. Always allow it to be a practice of running the equipment for 3-5 minutes after reassembling it to ensure you will find no leaks – mainly concentrate on the center of the filter dome where in fact the o-ring resides.
Effective Swimming Pool Maintenance Success Tip #3: Water Chemistry. Balancing your chemistry levels is an important variable as it pertains to properly maintaining your swimming pool. When any part of one’s water chemistry is off, it could cause a sequence reaction only causing the situation to have worse (and require more effort and investment property to rectify the problem).
The 3 main areas of water chemistry to target on are; your free chlorine levels, Total Alkalinity and pH. Your free chlorine levels should be 1-3ppm during summer time months and on the lower end of that range during the winter months. Your Total Alkalinity should take the number of 110 to 130 ppm.
Your TA essentially acts as a buffer for the pH to avoid wild and extreme swings in the total amount or strength of hydrogen in your swimming pool water. Your pH level should be between 7.4-7.8. Any higher or lower than that can result in the water irritating your skin, calcium buildup in your piping along with over the water line and can prematurely corrode your swimming pool equipment. It may result in damaged o-rings and when you yourself have a heater, it could cause internal damage to that particular as well.
Test and take corrective action on your own water chemistry on a weekly basis for proper swimming pool maintenance. Follow these 3 essential steps for sparkling swimming pool water that’ll have your pals, family and neighbors rendered speechless if they see your stunningly beautiful oasis!
I hope you’ve enjoyed this article. I share more free money and time saving tips right here. Go there now and start saving cash on your own swimming pool maintenance!